怎樣避免木工雕刻機的常見故障？

        三種控制方式：電腦雕刻機一是所有的運算工作由電腦控制完成，雕刻機在工作時電腦處于工作狀態，無法進行其它的排版工作，可能因電腦的誤操作而造成廢品；二是采用單片機的控制，雕刻機工作的同時可進行排版，但不能關閉電腦，可減少電腦誤操作造成的廢品；三是采用USB口傳輸數據，系統有著32M以上的內存容量，保存完文件即可脫離電腦、關閉電腦或進行其它排版，可大幅提高工作效率。

       木工雕刻機和廣告雕刻機沒有本質的區別，木工雕刻機以齒條機為主，主軸大，速度快，相對應的以速度和力度見長，價格高一些，廣告雕放機以切割廣告行業，PVC，芙蓉板，亞克力，雙色板為主，價格低，速度一般。雕刻機不能正常工作時，可能是其內部元件出了問題或者是其他方面的原因，雕銑機下面就經常出現的問題大體的介紹一下。主軸不能正常運轉。首先檢查變頻器LED顯示屏顯示的錯誤代碼（參見變頻器說明書錯誤代碼項），下面以YIXING變頻器為例說明。   

         三軸中有一軸不能動，此時要檢查一下相應軸所對應的驅動塊是否損壞。檢查方法可使用替換法：將不動軸所對應的航空插頭拔下插在其他能動軸所對應的驅動上。如果交換后不動軸走動正常，則可說明該軸所對應的驅動塊已損壞，需要更換好驅動塊。模具雕刻機如果不動軸還是不行就說明電纜線或電機有故障更換電纜線或者電機。三軸均不能動。此時檢查一下三軸航空插頭是否已和控制箱連接好，控制箱電源是否已打開。數據線是否和控制箱和電腦主機中控制卡連接好。如果以上都正常，則請和廠方聯系

本文由模具雕刻機編輯，轉載請注明來自：//ibiz88.com/